Inflexion Point Industries (IPI)

IPI is positioned to be an integral part of the seed-to-sale process in the;

  • Paper
  • Bio-plastics
  • Hempcrete
  • Biochar
  • Graphene
  • Emission reduction
  • Increased petroleum efficiency
  • Soil and water remediation
  • Plant growth enhancement
  • Rare earth element mining industries

We have built a national network of joint ventures with farmers, asset owners, suppliers, off take partners, and green technologies. IPI’s objective is to enhance and affect global initiatives for the betterment of our planet and reduction of our current carbon footprint.

Bringing Green Technology with Immediate Adoption Capabilities to Market

REMOVE Carbon Emission

The Sulev is reserved normally for Hybrids. Now, even normal ICEs can reach the SULEV specifications.

Cleanier Air, water & Light

Our Microbials, Nitro Cell and Ionization Technologies help Clean the soil, purify our water and remove toxins from the air.

Refining Waste Management

Our Technologies allow us to recycle materials to be recycled into Bioplastics, Biofuels and our Power generations equipment can use waste water to power the facilities while cleaning the water.

Global Sustainability

At IPI we are focused on disruptive tech that can create the largest impact on our Worlds environment.

Your identity is safe.

The only data taken and shared is the vin # of the vehicle that is installed with Nitro Cell.  This information is also submitted to the CARB program.  No personal information is shared.

Tony Harper

Oklahoma City, OK

GPM is a IP and property acquisition and disruptive technology implementation specialist that participates in sustainable agricultural manufacturing and processing for local, state, national sustainable solutions utilizing waste materials and specializing in environmental cleanup to produce energies, sustainable agricultural food programs, economic development through job creation.

Mike Tennyson

Yukon, OK

GPM is a IP and property acquisition and disruptive technology implementation specialist that participates in sustainable agricultural manufacturing and processing for local, state, national sustainable solutions utilizing waste materials and specializing in environmental cleanup to produce energies, sustainable agricultural food programs, economic development through job creation.

Eric Gousheh

Temecula, CA

GPM is a IP and property acquisition and disruptive technology implementation specialist that participates in sustainable agricultural manufacturing and processing for local, state, national sustainable solutions utilizing waste materials and specializing in environmental cleanup to produce energies, sustainable agricultural food programs, economic development through job creation.

405.409.3376

Oklahoma City, OK 73085

www.ipi.world

Connect with US Today!

We encourage you to submit the proper communication form.  We will respond to your inquiry within 48 hours of its submission.

F.A.Q Section

Have a query? Please check this question and answer section.  Also feel free to submit personal questions.

The Nitro Cell is installed on the throttle body blow by line to the engine. 

EO D-671 aftermarket approved device does not void the OEM manufactures warranty.

The Nitro Cell has a Lifetime warranty. It most cases it does not need to be replaced or cleaned.  It can be cleaned or replaced in minutes.

Typical install process (30 mins):

1. Pre-Install Emissions Test

2. Pre-Install Photo of Crankcase and Blow-by-lines.

3. Install of NitroCell

4. Post-Install Photo of Nitrocell in line.

5. 5 minutes (5 Miles Recommended) to heat engine in order to complete Post-Install Emissions Test.

No Out of Pocket from Consumers, Commercial or Governmental Agencies because the Nitro Cell is an Executive Order through the CARB rebate program.

Over time on an existing motor, the Nitro Cell will remove slug and debris from both the engine block and the Catalectic Convertor.

The Nitro Cell can be installed on small, large, gas, diesel, locomotive and jet engines.

The NitroCell is an inline ionized catalyst that can be applied to any internal combustion engine’s blow by hose in a matter of minutes. Once fuel passes through the NitroCell it is refined, ionized, and then recycled back into the cylinder to reignite, resulting in a boost in fuel efficiency from the current 50% to 90%+, while simultaneously cleaning engine buildup, and cutting CO2 and NOx emissions by half above EPA standards, resulting in Super Ultra Low Emission Vehicle status which is normally reserved for hybrid vehicles.